j'ai acheté ce Laptop d'occasion avec windows 7 et mis en dualboot Mint 18.3 cinnamon 64bit.
Après 4 ou 5 démarrages j'ai reçu l'info que le disque dur fonctionnait mal. J'ai fait un memtest, qui n'a pas trouvé d'anomalies. Et maintenant il ne se monte même plus. Alors j'ai trouvé cette commande dans le forum Ubuntu:
Code : Tout sélectionner
mint@mint ~ $ sudo smartctl -a /dev/sda
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-38-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA (AF)
Device Model: WDC WD7500BPVT-22HXZT3
Serial Number: WD-WXL1E61NXAU8
LU WWN Device Id: 5 0014ee 601776fc6
Firmware Version: 01.01A01
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Feb 10 13:27:16 2018 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (16500) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 162) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 181 178 021 Pre-fail Always - 1950
4 Start_Stop_Count 0x0032 088 088 000 Old_age Always - 12321
5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 561
7 Seek_Error_Rate 0x002e 179 178 000 Old_age Always - 490
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 4579
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 093 093 000 Old_age Always - 7968
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 1670
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 23
193 Load_Cycle_Count 0x0032 156 156 000 Old_age Always - 133733
194 Temperature_Celsius 0x0022 113 103 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 044 044 000 Old_age Always - 156
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 41544 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 41544 occurred at disk power-on lifetime: 4578 hours (190 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 00:10:33.253 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:10:33.248 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:10:33.248 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:10:33.248 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:10:33.243 IDENTIFY DEVICE
Error 41543 occurred at disk power-on lifetime: 4578 hours (190 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 00:10:33.248 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:10:33.248 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:10:33.243 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 00 00:10:33.227 SET FEATURES [Enable SATA feature]
Error 41542 occurred at disk power-on lifetime: 4578 hours (190 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 00:10:33.248 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:10:33.243 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 00 00:10:33.227 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:10:33.224 IDENTIFY DEVICE
Error 41541 occurred at disk power-on lifetime: 4578 hours (190 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 00:10:33.227 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:10:33.224 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:10:33.223 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:10:33.223 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:10:33.219 IDENTIFY DEVICE
Error 41540 occurred at disk power-on lifetime: 4578 hours (190 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 00:10:33.223 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:10:33.223 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 00:10:33.219 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 00 00:10:33.208 SET FEATURES [Enable SATA feature]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Un grand merci