Résolu le 29-11-18 lire un smartctl

Tous les sujets touchant à la sécurité du système.
Répondre
calixtus06
Messages : 172
Enregistré le : ven. 11 nov. 2016 19:34
Localisation : Vinay (38)

lire un smartctl

Message par calixtus06 »

Hello je ne sais comment lire un smartctl.

Quelqu'un peut il me guider ?

Merci d'avance

Nico

Code : Tout sélectionner

atelier-HP-Compaq-dx2300-Microtower ~ # smartctl --all /dev/sda
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-34-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, http://www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10
Device Model:     ST3250820AS
Serial Number:    6QF38EAH
Firmware Version: 3.CHL
User Capacity:    250 059 350 016 bytes [250 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7 (minor revision not indicated)
Local Time is:    Tue Oct  2 18:11:53 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (  39)	The self-test routine was interrupted
					by the host with a hard or soft reset.
Total time to complete Offline 
data collection: 		(  433) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  72) minutes.
SCT capabilities: 	       (0x0035)	SCT Status supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   253   006    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0002   095   095   000    Old_age   Always       -       0
  4 Start_Stop_Count        0x0033   099   099   020    Pre-fail  Always       -       1101
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   088   060   030    Pre-fail  Always       -       714816028
  9 Power_On_Hours          0x0032   074   074   000    Old_age   Always       -       23530
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0033   099   099   020    Pre-fail  Always       -       1089
184 End-to-End_Error        0x0033   100   253   097    Pre-fail  Always       -       0
187 Reported_Uncorrect      0x003a   100   100   000    Old_age   Always       -       0
189 High_Fly_Writes         0x0022   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x001a   066   054   000    Old_age   Always       -       34 (Min/Max 23/38)
194 Temperature_Celsius     0x0000   034   046   000    Old_age   Offline      -       34 (0 11 0 0 0)
195 Hardware_ECC_Recovered  0x0032   062   055   000    Old_age   Always       -       204662296
197 Current_Pending_Sector  0x0000   100   100   000    Old_age   Offline      -       0
198 Offline_Uncorrectable   0x0000   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0000   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Interrupted (host reset)      70%         1         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

atelier-HP-Compaq-dx2300-Microtower ~ # 
Modifié en dernier par arghlub le mar. 2 oct. 2018 18:41, modifié 1 fois.
Raison : Remplacement des balises [url] par des [code] pour le code-terminal
ACER ASPIRE M3641,
KDE Plasma 5.6.5, Distro: Linux Mint 18 Sarah, Intel model: DG41CN, Quad core Intel Core2 Quad Q6600, speed/max: 1596/2394 MHz, NVIDIA G73 [GeForce 7600 GT],
Network Card: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
Drives: HDD Total Size: 160.0GB (34.1% used)
Memory: 3 go DDR2 Synchrone 667 MHz (1,5 ns)
Kernel: 4.4.0-21-generic x86_64 (64 bit),

Avatar du membre
yomane
Messages : 201
Enregistré le : mar. 16 août 2016 16:36
Contact :

Re: lire un smartctl

Message par yomane »

Bonjour @calixtus06

On va dire que si tu n'as une petite connaissance de la langue de shakespeare, c'est pas gagné.. :l (c'est de l'humour)

Pti conseil, ne lance de commande sous linux, si tu en connais pas la portée.. (hors résolution de problème fournit dans les forums)

Infos : smartools, est un paquetage qui offrent 2 utilitaires 1 pour surveiller ton disque dur, et un autre (smartctl) pour les lire les infos de ton disque dur et modifier ses paramètres...
Pour ce qui est de la traduction des infos...a moins d'avoir un problème précis...on va dire ça va être un peu chiant de faire une traduction
Image
[/img]Discord : Invitation => https://discord.gg/HBWnGy3
"Jamais Souris ne confie a un seul trou sa Destinée"

calixtus06
Messages : 172
Enregistré le : ven. 11 nov. 2016 19:34
Localisation : Vinay (38)

Re: lire un smartctl

Message par calixtus06 »

bonjour et merci de ta réponse.

En fait je veux juste savoir si je dois ou pas envisager de changer de disque dur.
ACER ASPIRE M3641,
KDE Plasma 5.6.5, Distro: Linux Mint 18 Sarah, Intel model: DG41CN, Quad core Intel Core2 Quad Q6600, speed/max: 1596/2394 MHz, NVIDIA G73 [GeForce 7600 GT],
Network Card: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
Drives: HDD Total Size: 160.0GB (34.1% used)
Memory: 3 go DDR2 Synchrone 667 MHz (1,5 ns)
Kernel: 4.4.0-21-generic x86_64 (64 bit),

Avatar du membre
serged
Messages : 823
Enregistré le : jeu. 16 juil. 2015 07:59
Localisation : Montrouge (France)

Re: lire un smartctl

Message par serged »

En fait, les utilitaires graphiques (comme gsmartctl) affichent en rouge ce qui ne va pas....

Sinon, sapiens cum wikipedia.
(voir aussila version anglaise, plus complète)
LinuxMint Virginia Cinnamon et d'autres machines en MATE, XFCE... 20.x , 21.x ou 19.x
Tour : Asus F2A55 / AMD A8-5600K APU 3,6GHz / RAM 16Go / Nvidia GeForce GT610 / LM21.1 Cinnamon
Portable : LDLC Mercure MH : Celeron N3450 /RAM 4Go / Intel HD graphics 500 i915 / biboot Win 10 (sur SSD) - LM21.1 MATE (sur HDD)

calixtus06
Messages : 172
Enregistré le : ven. 11 nov. 2016 19:34
Localisation : Vinay (38)

Re: lire un smartctl

Message par calixtus06 »

merci beaucoup !!
ACER ASPIRE M3641,
KDE Plasma 5.6.5, Distro: Linux Mint 18 Sarah, Intel model: DG41CN, Quad core Intel Core2 Quad Q6600, speed/max: 1596/2394 MHz, NVIDIA G73 [GeForce 7600 GT],
Network Card: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
Drives: HDD Total Size: 160.0GB (34.1% used)
Memory: 3 go DDR2 Synchrone 667 MHz (1,5 ns)
Kernel: 4.4.0-21-generic x86_64 (64 bit),

Répondre