Disque SSHD
Posté : lun. 14 oct. 2019 20:50
Bonjour,
Je viens d'acquérir un disque hybride SSHD, 2.5'' Seagate Firecuda 1To, que j'ai branché dans un adaptateur à la place du lecteur DVD de mon ordi portable (PC1 ci-dessous). Avant d'installer quelque chose dessus, je me dis tiens, je vais voir les données SMART. Ce qui m'inquiète un peu, Raw_Read_Error_Rate et Seek_Error_Rate et la température sont élevés. Je me demande s'il y aurait un défaut de fabrication ou s'il aurait subi un choc durant le transport. Ou peut-être que smartctl ne gère pas bien ce genre de disque. Cependant les tests ne donnent pas d'erreur. Qu'en pensez-vous ? je copie les valeurs ci-dessous.
merci. Belle soirée.
Je viens d'acquérir un disque hybride SSHD, 2.5'' Seagate Firecuda 1To, que j'ai branché dans un adaptateur à la place du lecteur DVD de mon ordi portable (PC1 ci-dessous). Avant d'installer quelque chose dessus, je me dis tiens, je vais voir les données SMART. Ce qui m'inquiète un peu, Raw_Read_Error_Rate et Seek_Error_Rate et la température sont élevés. Je me demande s'il y aurait un défaut de fabrication ou s'il aurait subi un choc durant le transport. Ou peut-être que smartctl ne gère pas bien ce genre de disque. Cependant les tests ne donnent pas d'erreur. Qu'en pensez-vous ? je copie les valeurs ci-dessous.
merci. Belle soirée.
Code : Tout sélectionner
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-38-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST1000LX015-1U7172
Serial Number: WL1YCG13
LU WWN Device Id: 5 000c50 0c043789f
Firmware Version: SDM1
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Oct 14 20:45:41 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 166) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 006 Pre-fail Always - 8648
3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 3
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 253 045 Pre-fail Always - 759911
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 2 (153 145 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 3
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 253 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 055 050 040 Old_age Always - 45 (Min/Max 23/50)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 3
194 Temperature_Celsius 0x0022 045 050 000 Old_age Always - 45 (0 22 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 2 (204 0 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 0
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 8648
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 2 -
# 2 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.