Forum-Francophone-LinuxMint.fr

Bonjour

J'ai un drôle de message sur un disque dur que je ne sais pas interpréter
J'aimerais pouvoir effacer ou corriger ce problème
C'est un vieux PC portable, mais je l'ai upgradé et il tourne plutôt bien, même avec Mate Xia 22.1
Il démarre en moins de 20 secondes, ce qui est plutôt honorable pour un vieux clou de 2013

Tout semble fonctionner parfaitement, c'est par hasard en lançant un Gsmartcontroll que je suis tombé là dessus

Code : Tout sélectionner

Complete error log:

SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 2486 (device log contains only the most recent 8 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2486 [5] occurred at disk power-on lifetime: 128 hours (5 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 41 00 00 00 00 00 0a f1 f8 40 00  Error: ICRC, ABRT at LBA = 0x000af1f8 = 717304

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 d5 00 00 00 00 00 0a f1 f9 40 08     00:00:00.074  WRITE FPDMA QUEUED
  61 00 00 00 01 00 00 00 0a f1 f8 40 08     00:00:00.141  WRITE FPDMA QUEUED
  ec 00 00 00 01 00 00 00 00 00 00 00 08     00:00:00.141  IDENTIFY DEVICE
  ef 00 10 00 02 00 00 00 00 00 00 a0 08     00:00:00.141  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:00.141  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2485 [4] occurred at disk power-on lifetime: 128 hours (5 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 00 00 00 40 00  Error: 

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  00 00 00 00 00 00 00 00 00 00 00 00 08     00:00:00.074  NOP [Abort queued commands]
  60 00 10 00 01 00 00 00 00 14 79 40 08     00:00:00.105  READ FPDMA QUEUED
  60 00 10 00 01 00 00 00 00 14 78 40 08     00:00:00.105  READ FPDMA QUEUED
  60 00 10 00 01 00 00 00 00 14 77 40 08     00:00:00.105  READ FPDMA QUEUED
  60 00 10 00 01 00 00 00 00 14 76 40 08     00:00:00.105  READ FPDMA QUEUED

Error 2484 [3] occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 01 00 00 00 8f de 39 ec 00  Error: ICRC, ABRT at LBA = 0x0c8fde39 = 210755129

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  ca 00 00 00 01 00 00 00 8f de 39 ec 08     00:00:14.452  WRITE DMA
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.420  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     00:00:14.420  IDENTIFY DEVICE
  ef 00 03 00 42 00 00 00 00 00 00 a0 08     00:00:14.420  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.420  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2483 [2] occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 01 00 00 00 89 76 c4 ec 00  Error: ICRC, ABRT at LBA = 0x0c8976c4 = 210335428

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  ca 00 00 00 07 00 00 00 89 76 be ec 08     00:00:14.419  WRITE DMA
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.419  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     00:00:14.419  IDENTIFY DEVICE
  ef 00 03 00 42 00 00 00 00 00 00 a0 08     00:00:14.419  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.419  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2482 [1] occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 01 00 00 00 89 76 c4 ec 00  Error: ICRC, ABRT at LBA = 0x0c8976c4 = 210335428

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  ca 00 00 00 07 00 00 00 89 76 be ec 08     00:00:14.419  WRITE DMA
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.419  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     00:00:14.419  IDENTIFY DEVICE
  ef 00 03 00 42 00 00 00 00 00 00 a0 08     00:00:14.419  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.419  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2481 [0] occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 01 00 00 00 89 76 c4 ec 00  Error: ICRC, ABRT at LBA = 0x0c8976c4 = 210335428

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  ca 00 00 00 07 00 00 00 89 76 be ec 08     00:00:14.418  WRITE DMA
  ca 00 00 00 01 00 00 00 00 61 f8 ec 08     00:00:14.418  WRITE DMA
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.418  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     00:00:14.418  IDENTIFY DEVICE
  ef 00 03 00 42 00 00 00 00 00 00 a0 08     00:00:14.418  SET FEATURES [Set transfer mode]

Error 2480 [7] occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 01 00 00 00 89 76 c4 ec 00  Error: ICRC, ABRT at LBA = 0x0c8976c4 = 210335428

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  ca 00 00 00 07 00 00 00 89 76 be ec 08     00:00:14.418  WRITE DMA
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.418  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     00:00:14.418  IDENTIFY DEVICE
  ef 00 03 00 42 00 00 00 00 00 00 a0 08     00:00:14.418  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.418  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 2479 [6] occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  84 -- 51 00 01 00 00 00 00 61 f8 ec 00  Error: ICRC, ABRT at LBA = 0x0c0061f8 = 201351672

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  ca 00 00 00 01 00 00 00 00 61 f8 ec 08     00:00:14.417  WRITE DMA
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.417  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08     00:00:14.417  IDENTIFY DEVICE
  ef 00 03 00 42 00 00 00 00 00 00 a0 08     00:00:14.417  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 00 00 00 00 00 e0 08     00:00:14.417  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

J'ai bien compris qu'il y a eu des problème d'alimentation sur ce DD Sata, mais je ne sais pas comment l'interpreter ni comment le corriger
Du coup j'ai lancé un

Code : Tout sélectionner

sudo badblocks -v /dev/sda1

Qui m'a rassuré puisqu'il en résulte qu'aucun secteur n'est défectueux

Code : Tout sélectionner

Vérification des blocs 0 à 1465137559
Vérification des blocs défectueux (test en mode lecture seule) : 
complété                                                 
Passe complétée, 0 blocs défectueux repérés. (0/0/0 erreurs)

C'est grave Docteur ?
Puis je avoir confiance en ce DD de 1.5 Go ?
Il y a moyen d'effacer ce message ???
Merci d'avance

Merci Cyrille

Désolé, je n'avais pas pu répondre avant
Voici ce que ça donne

Code : Tout sélectionner

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Samsung SpinPoint M9T
Device Model:     ST1500LM006 HN-M151RAD
Serial Number:    S345J9AF701490
LU WWN Device Id: 5 0004cf 20dae4d6a
Firmware Version: 2BC10001
User Capacity:    1 500 301 910 016 bytes [1,50 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database 7.3/5528
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Apr  1 19:14:09 2025 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(15300) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 255) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   100   100   051    Pre-fail  Always       -       1
  2 Throughput_Performance  0x0026   252   252   000    Old_age   Always       -       0
  3 Spin_Up_Time            0x0023   088   088   025    Pre-fail  Always       -       3854
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       784
  5 Reallocated_Sector_Ct   0x0033   252   252   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   252   252   051    Old_age   Always       -       0
  8 Seek_Time_Performance   0x0024   252   252   015    Old_age   Offline      -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       154
 10 Spin_Retry_Count        0x0032   252   252   051    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       304
191 G-Sense_Error_Rate      0x0022   100   100   000    Old_age   Always       -       1
192 Power-Off_Retract_Count 0x0022   252   252   000    Old_age   Always       -       0
194 Temperature_Celsius     0x0002   064   063   000    Old_age   Always       -       24 (Min/Max 14/44)
195 Hardware_ECC_Recovered  0x003a   100   100   000    Old_age   Always       -       0
196 Reallocated_Event_Count 0x0032   252   252   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   252   252   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   252   252   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0036   096   096   000    Old_age   Always       -       2485
200 Multi_Zone_Error_Rate   0x002a   100   100   000    Old_age   Always       -       2
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       6
225 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       3430

SMART Error Log Version: 1
ATA Error Count: 1992 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1992 occurred at disk power-on lifetime: 128 hours (5 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 00 00 00 40

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  18 9f 18 9f 18 f0 18 9f      10:54:18.685  RECALIBRATE [RET-4]
  00 00 00 00 00 00 00 08      00:00:00.074  NOP [Abort queued commands]
  60 10 01 79 14 00 40 08      00:00:00.105  READ FPDMA QUEUED
  60 10 01 78 14 00 40 08      00:00:00.105  READ FPDMA QUEUED
  60 10 01 77 14 00 40 08      00:00:00.105  READ FPDMA QUEUED

Error 1991 occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 39 de 8f ec  Error: ICRC, ABRT at LBA = 0x0c8fde39 = 210755129

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ca 00 01 39 de 8f ec 08      00:00:14.452  WRITE DMA
  27 00 00 00 00 00 e0 08      00:00:14.420  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 08      00:00:14.420  IDENTIFY DEVICE
  ef 03 42 00 00 00 a0 08      00:00:14.420  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 08      00:00:14.420  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 1990 occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 c4 76 89 ec  Error: ICRC, ABRT at LBA = 0x0c8976c4 = 210335428

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ca 00 07 be 76 89 ec 08      00:00:14.419  WRITE DMA
  27 00 00 00 00 00 e0 08      00:00:14.419  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 08      00:00:14.419  IDENTIFY DEVICE
  ef 03 42 00 00 00 a0 08      00:00:14.419  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 08      00:00:14.419  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 1989 occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 c4 76 89 ec  Error: ICRC, ABRT at LBA = 0x0c8976c4 = 210335428

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ca 00 07 be 76 89 ec 08      00:00:14.419  WRITE DMA
  27 00 00 00 00 00 e0 08      00:00:14.419  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 08      00:00:14.419  IDENTIFY DEVICE
  ef 03 42 00 00 00 a0 08      00:00:14.419  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 08      00:00:14.419  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 1988 occurred at disk power-on lifetime: 122 hours (5 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 c4 76 89 ec  Error: ICRC, ABRT at LBA = 0x0c8976c4 = 210335428

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ca 00 07 be 76 89 ec 08      00:00:14.418  WRITE DMA
  ca 00 01 f8 61 00 ec 08      00:00:14.418  WRITE DMA
  27 00 00 00 00 00 e0 08      00:00:14.418  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 08      00:00:14.418  IDENTIFY DEVICE
  ef 03 42 00 00 00 a0 08      00:00:14.418  SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Completed [00% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

The above only provides legacy SMART information - try 'smartctl -x' for more

Si je comprends, il aurait eu un problème d'alimentation il y a 5 jours et 2 heures ?
Je ne m'explique pas ce désordre, mais pourquoi pas

Merci

Ca me rassure
Comme d'habitude très efficace
Bonne soirée

Forum-Francophone-LinuxMint.fr

Disque ATA Error Count: 2486 - RESOLU

Disque ATA Error Count: 2486 - RESOLU

Re: Disque ATA Error Count: 2486

Re: Disque ATA Error Count: 2486